Author: flash rom

Mini ST-LINK/V2 on a small single board, an extreme low cost solution for in-circuit debugger/programmer for STM8 and STM32.
Features
? Onboard 500mA self-recovery fuse to avoid harming by short circuit
? Dual voltage output (3.3V/5V), easy for debugging/programming
? Standard USB interface for direct connection to PC
? Debugging/Programing performance
o Debugging : run at full-speed, single-stepped, breakpoints, viewing variables and registers, etc.
o Programming : supports FLASH ROM, EEPROM, AFR, etc.
o USB2.0 combined with SWIM/SWD interfaces : quick response for debugging & fast speed for programming
? Upgradable firmware
o The firmware is upgradable to support more devices in the future
o Automatically upgraded
? Supported software
o ST-LINK Utility v2.0 (or higher ver.)
o STVD Version 4.2.1 (or higher ver.)
o STVP Version 3.2.3 (or higher ver.)
o IAR EWARM Revision v6.20 (or higher ver.)
o IAR EWSTM8 Revision v1.30 (or higher ver.)
o KEIL RVMDK Revision v4.21 (or higher ver.)
o ATOLLIC
o TASKING
? Supported devices
o All the STM8 devices with SWIM interface
o All the STM32 devices with SWD interface
Next Company trademark registered trademarks. Next Company shop is the only authorized stores. all violations will be complaints!

Please confirm model in the title.

Specifications

Type : Accessories

Accessories Function : Connector

Model : ST-LINK/V2

Dimension(cm) : 5*2*1

Net Weight(kg) : 0.013

QX Electronics The Best ST-LINK/V2 ST-LINK V2(CN) ST LINK STLINK Emulator STM8 STM32 Original

Package Include: Please refer to the picture and the product title.

ST STM32 STM32F4 STM32F407 MCU Discovery Evaluation Development Board kit embedded ST-LINK/V2 debugger @XYG

Type:Accessories,
Accessories Function:Connector,
Model:ST-LINK/V2,
Dimension(cm):5*2*1,
Net Weight(kg):0.013,

STMicroelectronics STM32VLDISCOVERY – Development Boards Kits – Arm Discovery Stm32F100 Embedded St-Link Brd

Functions and features:
1. Support all STM32 series SWD interface debug.
2. Support all STM8 series debug.
3. Support development environment:
1>.ST-LINK Utility 2.0 and the version latest than it.
2>.STVD 4.2.1 and the version latest than it.
3>.STVP 3.2.3 and the version latest than it.
4>.IAR EWARM V6.20 and the version latest than it.
5>.IAR EWSTM8 V1.30 and the version latest than it.
6>.KEIL RVMDK V4.21 and the version latest than it.
4. Support firmware upgrade automatically
5. Please open driver and code by administrator mode in WIN WISTA/WIN 7/WIN 8 system.

Package Including:
1. ST-LINK V2 1PCS
2. Dupont Cables 4PCS

Description:
Mini ST-LINK/V2 on a small single board, an extreme low cost solution for in-circuit debugger/programmer for STM8 and STM32.

Package Contains:
ST-LINK/V2 (mini) × 1
4-pin custom connector cable × 1

STMICROELECTRONICS ST-LINK/V2 ICD/PROGRAMMER, USB 2.0, JTAG, FOR STM8, STM32

1.100% Brand new and high quality.
2.Support the full range of STM32 SWD interface debugging, simple interface (including power supply), 4 line speed, stable work; Interface definition shell directly address! Don’t need to read instructions!
3.Support all series STM8 SWIM download debugging (common development environment such as IAR, STVD etc.) are supported. Support the software version is as follows:
ST – LINK Utility 2.0 and above
STVD 2 and above
STVP 3.2.3 and above
IAR EWARM V6.20 and above
IAR EWSTM8 V1.30 and above
KEIL RVMDK V4.21 and above
4.Support the firmware upgrade automatically, to ensure that the ST company product support. When they leave the firmware has been upgraded to the latest V2.J17.S4
5.Increase the 5 v power output, the output it can protect the I/O port, not afraid of error cause damage of ST – LINK V2!
6.Easy interface to use pure copper plating 2.54 spacing horn, with 20 cm DuPont line, can deal with different target board line sequence, flexible connection;
7.Use U disk aluminum alloy shell to protect the mainboard, convenient to carry, not afraid of static electricity, not afraid of tumbling.
8.Material: Metal, plastic, electronic parts
9.Color: Red, Blue, Green, Yellow, Black, Purple, Brown, Silver (We will send color at random, thank you for your understanding)
10.Size: Approx. 5.5 x 2 x 0.8cm (L*W*H)

What’s in the package:
1 x ST-Link V2 STM8 STM32 Programmer
1 x 20cm Debug DuPont Line

Supported software versions are as follows:
ST-LINK Utility 2.0 and above
STVD 4.2.1 and above
STVP 3.2.3 and above
IAR EWARM V6.20 and above
IAR and EWSTM8 V1.30 and V4.21 and above
KEIL RVMDK

Note 1:
ST-LINK / V1 with ST-LINK / V2 Two drive mode is completely different, if you replace the V2 for V1 need install ST-LINK/V2 drive and you may need to update software

Note 2:
VISTA, WIN7, WIN8 user, please use administrator mode to install drivers and applications
If dynamic signature issue in the case, please trust ST LINK V2 drive (WIN8 may need to turn off the signature drive to force only after successful installation).
After the installation is complete, the device manager will have “STMicroelectronics STLink dongle”

Package include:
1x ST-LINK / V2
5x Dupont cable
1x 4P (XH2.54) debugging cable

Feature:

Supports full range of STM32 SWD 4-wire interface debug interface definition directly marked on the shell
Supports full range of STM8 SWIM download debugging, supported software versions are as follows:
¢Ù ST-LINK Utility 2.0 and above
¢Ú STVD 4.2.1 and above
¢Û STVP 3.2.3 and above
¢Ü IAR EWARM V6.20 and above
¢Ý IAR EWSTM8 V1.30 and above
¢Þ KEIL RVMDK V4.21 and above
Supports automatic firmware upgrade, the factory has been upgraded to the latest firmware V2.J17.S4
Increase 5V power output, the output I / O port protection are not afraid of operational errors caused by ST-LINK V2 damage!
0.54 interface uses simple horns seat pitch, equipped with DuPont line, can respond to different target line sequence, flexible wiring;
Red and blue color LED indicator
Motherboard with internal resettable fuse 500MA

Note:

This product will be packaged in Random Color

Package included:

1 x ST-LINK V2 Emulator Downloader Programmer Support STM8 STM32
1 x DuPont line

Features

STM32 microcontrollers in 32-pin packages
extension with Arduino nano connectivity
mbed-enabled
on-board ST-LINK/V2-1 debugger/programmer
USB reenumeration capability: three different interfaces supported on USB:
Virtual Com port
mass storage
debug port
flexible board power supply:
USB VBUS
external source
three LEDs:
USB communication (LD1), power LED (LD2), user LED (LD3)
reset push button
supported by wide choice of Integrated Development Environments (IDEs) including IAR, Keil, GCC-based IDEs (AC6 SW4STM32, …)

DISTRIBUTION LIST

1 * NUCLEO-F303K8

Note: Due to different production batches, product’s color may be different.

Features

STM32 microcontroller with LQFP64 package
Two types of extension resources
Arduino Uno Revision 3 connectivity
STMicroelectronics Morpho extension pin headers for full access to all STM32 I/Os
mbed-enabled (mbed.org)
On-board ST-LINK/V2-1 debugger/programmer with SWD connector
selection-mode switch to use the kit as a standalone ST-LINK/V2-1
Flexible board power supply
USB VBUS or external source(3.3 V, 5 V, 7 – 12 V)
Power management access point
Three LEDs
USB communication (LD1), user LED (LD2), power LED (LD3)
Two push buttons: USER and RESET
USB re-enumeration capability: three different interfaces supported on USB
Virtual Com port
Mass storage
Debug port
Supported by wide choice of Integrated Development Environments (IDEs) including IAR, Keil, GCC-based IDEs

DISTRIBUTION LIST

1 * NUCLEO-F303RE

Note: Due to different production batches, product’s color may be different.

Features

STM32 microcontroller with LQFP64 package
Two types of extension resources
Arduino Uno Revision 3 connectivity
STMicroelectronics Morpho extension pin headers for full access to all STM32 I/Os
mbed-enabled (mbed.org)
On-board ST-LINK/V2-1 debugger/programmer with SWD connector
selection-mode switch to use the kit as a standalone ST-LINK/V2-1
Flexible board power supply
USB VBUS or external source(3.3 V, 5 V, 7 – 12 V)
Power management access point
Three LEDs
USB communication (LD1), user LED (LD2), power LED (LD3)
Two push buttons: USER and RESET
USB re-enumeration capability: three different interfaces supported on USB
Virtual Com port
Mass storage
Debug port
Supported by wide choice of Integrated Development Environments (IDEs) including IAR, Keil, GCC-based IDEs

DISTRIBUTION LIST

1 * NUCLEO-F091RC

Note: Due to different production batches, product’s color may be different.

Features

STM32 microcontroller with LQFP64 package
Two types of extension resources
Arduino Uno Revision 3 connectivity
STMicroelectronics Morpho extension pin headers for full access to all STM32 I/Os
mbed-enabled (mbed.org)
On-board ST-LINK/V2-1 debugger/programmer with SWD connector
selection-mode switch to use the kit as a standalone ST-LINK/V2-1
Flexible board power supply
USB VBUS or external source(3.3 V, 5 V, 7 – 12 V)
Power management access point
Three LEDs
USB communication (LD1), user LED (LD2), power LED (LD3)
Two push buttons: USER and RESET
USB re-enumeration capability: three different interfaces supported on USB
Virtual Com port
Mass storage
Debug port
Supported by wide choice of Integrated Development Environments (IDEs) including IAR, Keil, GCC-based IDEs

DISTRIBUTION LIST

1 * NUCLEO-F070RB

Note: Due to different production batches, product’s color may be different.

Description

The ST-LINK is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families. The SWIM and JTAG/SWD interface is used to communicate with the STM8 or STM32 microcontroller located on your own application board.

On the PC side, the USB full speed interface is used to communicate with:

ST Visual Develop (STVD) or ST Visual Program (STVP) software from
STMicroelectronic’s for the STM8,
ATOLLIC, IAR and KEIL Integrated Development Environments for the STM32.

Key Features

5 V power supplied by USB connector
USB 2.0 full speed interface compatible
USB standard A to micro cable provided
SWIM specific features:
1.65 V to 5.5 V application voltage supported on SWIM interface
SWIM low speed and high speed modes supported
SWIM programming speed rate:
9.7 Kbytes/s in low speed
12.8 Kbytes/s in high speed
SWIM cable for connection to an application with pin headers or 2.54 mm pitch connector
JTAG/SWD specific features:
3 V to 3.6 V application voltage supported on JTAG/SWD interface and 5 V tolerant inputs
JTAG/SWD cable provided for connection to a standard JTAG 20-pin pitch 2.54 MM connector
Direct firmware update feature supported
Status LED which blinks during communication with PC
Operating temperature 0 to 50 degree

Distribution List:

1 * ST-LINK
1 * USB type A to micro cable
1 * 20-pin JTAG/SWD flat ribbon
1 * 4-pin SWIM separate-wires cable

Puuli ARM Ulink II 2 Emulator ARM Programmer USB JTAG Realview Debug Adapter Cortex

Features:

Supports various ARM7, ARM9, Cortex-M, 8051, and C166 devices, JTAG speed up to 10MHz
Ulink 2 USB JTAG Emulator ARM9 Cortex Keil Ulink II GH2
Serial Wire Viewer (SWV) Data Trace for Cortex-M up to 1Mbit/s (UART mode)
ARM USB Compatible JTAG Adapter Debugger Keil Ulink-II
Plug-and-Play installation using standard Windows USB drivers
Conveniently carried out target hardware on-chip debugging (using on-chip JTAG, SWD, and OCDS), Flash Programming

Package Included:

1 X Puuli ARM Ulink II 2 Emulator ARM Programmer USB JTAG Realview Debug Adapter Cortex

Written by the director of ARM’s worldwide academic program, this volume gives computer science professionals and students an edge, regardless of their preferred coding language. For those with some basic background in digital logic and high-level programming, the book examines code relevant to hardware and peripherals found on today’s microcontrollers and looks at situations all programmers will eventually encounter.

The book’s carefully chosen examples teach easily transferrable skills that will help readers optimize routines and significantly streamline coding, especially in the embedded space.

This book is easily adaptable for classroom use. Instructors can access features that include a solutions manual, assembly language basics, problems, and actual code. The book also provides access to a fully functional evaluation version of the RealView Microcontroller Development Kit from Keil.

While it is still an important skill, getting good instruction in assembly language is not easy. The availability of languages such as C and Java foster the belief that engineers and programmers need only address problems at the highest levels of a program’s operation. Yet, even modern coding methods, when done well, require an understanding of basic assembly methods such as those gained by learning ARM. Certain features that are the product of today’s hardware, such as coprocessors or saturated math operations, can be accessed only through the hardware’s native instructions. For that matter, any programmer wishing to achieve results as exact as his or her intentions needs to possess a mastery of machine code basics as taught in the pages of this book.

Of the 13 billion microprocessor-based chips shipped in the last year, nearly 3 billion were ARM-based, making operational knowledge of ARM an essential component of any programmer’s tool kit. That it can be applied with most any language makes it invaluable.

KEIL ULINK2 DEBUG ADAPTER, FOR ARM7, ARM9, 8051, C166